Cisco Rv340 Client To Site Vpn Setup

admin



  1. Cisco Rv340 Client To Site Vpn Setup Download
  2. Cisco Rv340 Client To Site Vpn Setup Free
  3. Cisco Rv340 Client To Site Vpn Setup Password
  4. Cisco Rv340 Client To Site Vpn Setup

Plus Not RV345, RV345P, and RV340W Not Working Surf The Router acts as a in this article will for client licenses only. VPN connection on the Set Up and an extremely difficult task. IOS Router Configure Secure Router Rv350 V. Private Network (VPN Configure Client-to-Site Virtual Cisco RV340, RV345. TheGreenBow VPN Client is a third-party VPN client application that makes it possible for a host device to configure a secure connection for site-to-site IPSec tunnel with the RV34x Series Router. In the diagram, the computer will connect to the file server in the office outside its network to access its resources. Cisco RV340 as VPN Client I am attempting to set up a Cisco RV340 router to route all internet traffic through a VPN service such as IPVanish, Nord VPN, TorGuard, PIA, etc. I am having trouble figuring out which of these services will support the protocols used by the RV340.

Objective

In a Client-to-Site Virtual Private Network (VPN) connection, clients from the Internet can connect to the server to access the corporate network or Local Area Network (LAN) behind the server but still maintains the security of the network and its resources. This feature is very useful since it creates a new VPN tunnel that would allow teleworkers and business travelers to access your network by using a VPN client software without compromising privacy and security.

The objective of this document is to show you how to configure Client-to-Site VPN connection on the RV34x Series Router.

Applicable Devices

  • RV34x Series

Software Version

Cisco Rv340 Client To Site Vpn Setup
  • 1.0.01.16

Configure Client-to-Site VPN

Step 1. Log in to the router web-based utility and choose VPN > Client-to-Site.

Step 2. Click the Add button under IPSec Client-to-Site Tunnels section.

Step 3. In the Add a New Tunnel area, click the Cisco VPN Client radio button.

Step 4. Check the Enable check box to enable the configuration.

Step 5. Enter a group name in the field provided. This will serve as identifier for all the member of this group during the Internet Key Exchange (IKE) negotiations.

Note: Enter characters between A to Z or 0 to 9. Spaces and special characters are not allowed for the group name. In this example, TestGroup is used.

Step 6. Click on the drop-down list to choose the Interface. The options are:

  • WAN1
  • WAN2
  • USB1
  • USB2

Note: In this example, WAN1 is chosen. This is the default setting.

Step 7. In the IKE Authentication Method area, choose an authentication method to be used in IKE negotiations in IKE-based tunnel. The options are:

Cisco Rv340 Client To Site Vpn Setup Download

Vpn
  • Pre-shared Key — IKE peers authenticate each other by computing and sending a keyed hash of data that includes the Pre-shared Key. If the receiving peer is able to create the same hash independently using its Pre-shared key, it knows that both peers must share the same secret, thus authenticating the other peer. Pre-shared keys do not scale well because each IPSec peer must be configured with the Pre-shared key of every other peer with which it establishes a session.
  • Certificate — The digital certificate is a package that contains information such as a certificate identity of the bearer: name or IP address, the serial number expiration date of the certificate, and a copy of the public key of the certificate bearer. The standard digital certificate format is defined in the X.509 specification. X.509 version 3 defines the data structure for certificates.

Note: In this example, Pre-shared Key is chosen. This is the default setting.

Step 8. Enter a pre-shared key in the field provided. This will be the authentication key among your group of IKE peers.

Step 9. (Optional) Check the Enable check box for the Minimum Pre-shared Key Complexity to view the Pre-shared Key Strength Meter and determine the strength of your key. The strength of your key are defined as follows:

  • Red— The password is weak.
  • Orange— The password is fairly strong.
  • Green — The password is strong.

Note: You can check the Enable check box in the Show Pre-shared Key field to check your password in plain text.

Step 10. (Optional) Click on the plus icon in the User Group table to add a group.

Step 11. (Optional) Choose from the drop-down list whether the user group is for admin or for guests. If you created your own user group with user accounts, you can select it. In this example, we will be selecting TestGroup.

Note: TestGroup is a user group that we have created in System Configuration >User Groups.

Note: In this example, TestGroup is chosen. You can also check the box beside the user group and then click the Delete button if you want to delete a user group.

Step 12. Click on a radio button to choose a Mode. The options are:

  • Client — This option allows the client to request for an IP address and the server supplies the IP addresses from the configured address range.
  • Network Extension Mode (NEM) — This option allows clients to propose their subnet for which VPN services need to be applied on traffic between LAN behind server and subnet proposed by client.

Cisco Rv340 Client To Site Vpn Setup Free

Note: In this example, Client is chosen.

Step 13. Enter the starting IP address in the Start IP field. This will be the first IP address in the pool that can be assigned to a client.

Note: In this example, 192.168.100.1 is used.

Step 14. Enter the ending IP address in the End IP field. This will be the last IP address in the pool that can be assigned to a client.

Note: In this example, 192.168.100.100 is used.

Step 15. (Optional) Under the Mode Configuration area, enter the IP address of the primary DNS server in the field provided.

Note: In this example, 192.168.1.1 is used.

Step 16. (Optional) Enter the IP address of the secondary DNS server in the field provided.

Note: In this example, 192.168.1.2 is used.

Step 17. (Optional) Enter the IP address of the primary WINS server in the field provided.

Note: In this example, 192.168.1.1 is used.

Step 18. (Optional) Enter the IP address of the secondary WINS server in the field provided.

Note: In this example, 192.168.1.2 is used.

Step 19. (Optional) Enter the default domain to be used in the remote network in the field provided.

Note: In this example, sample.com is used.

Step 20. (Optional) In the Backup Server 1 field, enter the IP address or the domain name of the backup server. This will be where the device can start the VPN connection in case the primary IPSec VPN server fails. You can enter up to three backup servers in the fields provided. The Backup Server 1 has the highest priority among the three servers and the Backup Server 3 has the lowest.

Note: In this example, Example.com is used for Backup Server 1.

Step 21. (Optional) Check the Split Tunnel check box to enable split tunnel. Split Tunneling allows you to access the resources of a private network and the Internet at the same time.

Step 22. (Optional) Under the Split Tunnel Table, click the plus icon to add an IP address for split tunnel.

Cisco Rv340 Client To Site Vpn Setup

Step 23. (Optional) Enter the IP address and netmask of the split tunnel in the fields provided.

Note: In this example, 192.168.1.0 and 255.255.255.0 are used. You can also check the box and click on the Add, Edit, and Delete buttons to add, edit, or delete a split tunnel, respectively.

Step 24. (Optional) Check the Split DNS check box to enable split DNS. Split DNS allows you to create separate DNS servers for internal and external networks to maintain security and privacy of network resources.

Step 25. (Optional) Click the plus icon under the Split DNS Table to add a domain name for split DNS.

Step 26. (Optional) Enter the domain name of the split DNS in the field provided.

Note: In this example, labsample.com is used. You can also check the box and click on the Add, Edit, and Delete buttons to add, edit, or delete a split DNS, respectively.

Step 27. Click Apply.

Conclusion

You should now have successfully configured Client-to-Site connection on the RV34x Series Router.

Click on the following articles to learn more on the following topics:

View a video related to this article...

Overview

Stanford's VPN allows you to connect to Stanford's network as if you were on campus, making access to restricted services possible. To connect to the VPN from your Windows computer you need to install the Cisco AnyConnect VPN client.

Two types of VPN are available:

  • Default Stanford (split-tunnel). When using Stanford's VPN from home, we generally recommend using the Default Stanford split-tunnel VPN. This routes and encrypts all traffic going to Stanford sites and systems through the Stanford network as if you were on campus. All non-Stanford traffic proceeds to its destination directly.
  • Full Traffic (non-split-tunnel). This encrypts all internet traffic from your computer but may inadvertently block you from using resources on your local network, such as a networked printer at home. If you are traveling or using wi-fi in an untrusted location like a coffee shop or hotel, you may wish to encrypt all of your internet traffic through the Full Traffic non-split-tunnel VPN to provide an additional layer of security.

You can select the type of VPN you want to use each time you connect to the Stanford Public VPN.

Install the VPN client

  1. Download the Cisco AnyConnect VPN for Windows installer.
  2. Double-click the InstallAnyConnect.exe file.
  3. When a message saying the Cisco AnyConnect client has been installed, click OK.

Connect to the Stanford VPN

  1. Launch the Cisco AnyConnect Secure Mobility Client client.
    If you don't see Cisco AnyConnect Secure Mobility Client in the list of programs, navigate to Cisco > Cisco AnyConnect Secure Mobility Client.
  2. When prompted for a VPN, enter su-vpn.stanford.edu and then click Connect.
  3. Enter the following information and then click OK:
    • Group: select Default Stanford split- tunnel (non-Stanford traffic flows normally on an unencrypted internet connection) or Full Traffic non-split-tunnel (all internet traffic flows through the VPN connection)
    • Username: your SUNet ID
    • Password: your SUNet ID password

  4. Next, the prompt for two-step authentication displays. Enter a passcode or enter the number that corresponds to another option(in this example, enter 1 to authenticate using Duo Push to an iPad). Then click Continue.
    • You may have to scroll down the list to see all of your options.
    • If your only registered authentication method is printed list, hardware token, or Google Authenticator, the menu does not display. Enter a passcode in the Answer field and click Continue.
  5. Click Accept to connect to the Stanford Public VPN service.
  6. Once the VPN connection is established, a message displays in the lower-right corner of your screen, informing you that you are now connected to the VPN.

Cisco Rv340 Client To Site Vpn Setup Password

Disconnect from the Stanford VPN

Cisco Rv340 Client To Site Vpn Setup

  1. In the notification area, click the Cisco AnyConnect icon if it is displayed. Otherwise, go to your list of programs and click Cisco AnyConnect Secure Mobility Client.
  2. At the prompt, click Disconnect.